Insulation and ventilation basics for Auckland homes
Insulation and ventilation are usually discussed as separate jobs, but in a house they are one system. Insulation keeps surfaces warmer, so moisture in the air is less likely to condense on them. Ventilation removes the moisture in the first place. Do only one and the house tends to underperform: a well-insulated but sealed house stays damp, and a well-ventilated but uninsulated one is cold and costly to heat.
This is a plain-language guide to the order that makes sense for an existing Auckland house.
How old is the house, and how leaky?
Building guidance from the government puts houses into rough bands. According to the ventilation guide on building.govt.nz, homes built before the 1960s are typically very draughty, those from the 1960s to 1980s are quite draughty, and newer homes are much more airtight. A draughty villa gets accidental fresh air but loses heat. A recent, tightly built house holds heat but needs deliberate ventilation. Knowing which one you live in tells you which half of the problem is bigger.
The same guide makes a point worth remembering: if you insulate and draught-proof first, you gain control over ventilation, rather than relying on gaps in the building to do the job.
Ceilings: the first and easiest job
The government's insulation guidance for existing homes calls ceilings often the easiest and most effective place to start. Where there is a roof space, bulk insulation can be laid over the ceiling lining and framing. A rough rule of thumb: if what is there is thinner than about 120 mm, or thinner than the framing, add more, and fill any gaps.
Three practical checks apply:
- Switch off the power at the switchboard before going into the roof space.
- Leave a clearance around old downlights and other electrical equipment, for fire safety.
- If there is no roof space, insulate when the lining or roofing is next replaced, keeping a 25 mm gap between insulation and roofing underlay in most cases to avoid moisture problems.
For a sense of targets, the minimum R-values in Tenancy Services' insulation standard for rentals are ceiling R2.9 in climate zones 1 and 2 and R3.3 in zone 3, with underfloor R1.3 in all three. Those are rental minimums rather than ideals, but they are a useful floor. The standard also says existing insulation should be in reasonable condition, with no mould, dampness, damage or gaps.
Floors: check what is under there
Houses on piles have a subfloor space that is often easy to reach. Bulk fibre or polystyrene can be fitted between joists. If you find aluminium foil insulation, the building.govt.nz guidance says it is inadequate, can be a safety hazard near wiring, and that retrofitting or repairing foil is banned, so it should be replaced. If the subfloor is enclosed, a polythene ground sheet reduces moisture rising from the soil.
Concrete slabs are different. There is little to do underneath, and most heat is lost through the slab edges, so edge insulation can help where it is practical, provided it is protected from ground moisture and does not push water behind the cladding.
Windows: the weak point
Single glazing has very low resistance to heat flow, about one-twentieth that of an insulated wall, according to the same guidance. You do not need to replace every window. Prioritise the rooms you use and heat most. Secondary glazing, in acrylic or glass, performs about as well as new double glazing. Plain aluminium frames conduct heat and attract condensation, so thermally broken aluminium, PVC or timber frames are better choices. For old timber sashes that do not close properly, draught-stopping strips cost little and make a noticeable difference.
Walls: leave until you are already opening them
Retrofitting wall insulation is usually difficult and typically needs building consent. The practical advice is to do it when cladding or linings are being replaced, install building paper if none is present, and, if you consider blown-in insulation, have a registered or accredited building surveyor confirm the cladding is weathertight first. Poorly installed insulation can cause moisture problems, which is the opposite of the goal.
Ventilation: what actually works
The ventilation guide describes continuous mechanical ventilation as the most effective way to maintain fresh air, and more convenient than relying on open windows. Without a whole-house system, the advice is to open windows several times a day. Wet rooms need extractor fans that discharge outside. If you install a mechanical system, the supply air should be drawn from outdoors, not the roof space, which can be polluted.
The rental ventilation standard sets benchmarks you can borrow. Each habitable room should have a window, door or skylight that opens to the outside and can be fixed open, with openable area of at least 5% of the room's floor area. New kitchen extraction should have a duct of at least 150 mm or move at least 50 litres per second; new bathroom extraction, 120 mm or 25 litres per second. The same standard notes that recirculating systems, and fans that do not extract to the outdoors, do not count as meeting the standard.
A sensible order
For most existing Auckland houses, the order that returns the most for the least disruption is: fix leaks and drainage, top up ceiling insulation, deal with the subfloor, fit or repair extractor fans that vent outside, then look at windows. Walls come last, ideally as part of other work.