Looking after a timber deck
A timber deck is the most weather-exposed part of many Auckland houses, and it is also the part people stand on with a glass in hand. It ends up neglected because the damage is slow and mostly cosmetic until, one day, it is not. A short routine each year catches most problems while they are still cheap to fix.
What weather does to timber
BRANZ's good repair guide to timber decking explains the basic mechanism. Regular wetting and drying makes timber swell and shrink, and together with UV light and temperature changes this causes deterioration. That is why the guide spends time on the details of how a deck sheds water. Slat decks are fully exposed and are built with 3 to 6 mm gaps between boards so water can drain. The tongue-and-groove decking on many villas and bungalows is laid with a fall to the exterior so that water runs off, and even decking under a roofed veranda or porch is still exposed to weather.
In other words, every deck's durability depends on water leaving it quickly. Anything that holds water, such as leaves in the gaps, a pot saucer, a board that has cupped, or a blocked drain at the edge, is where decay starts.
The yearly inspection
Choose a dry day, and work from the top down.
- Surface. Look for boards that are cracked, soft, split or sunken. Push a screwdriver into suspect spots; sound timber resists, decayed timber crumbles.
- Fixings. Check for popped nails and loose or rusted screws. They are a trip hazard and let water into the timber. Tighten or replace them.
- Gaps and drainage. Clear debris from between boards with a thin blade, and make sure water can leave the edges of the deck.
- The junction with the house. This is where water tends to collect, so look at it closely. Clear leaves and dirt, and check that cladding and any flashing above the deck look intact.
- From below, if you can see it. Look at joists and bearers for rot, staining and rust. If the deck is high enough that you must crawl under it, take a torch and look for mould and sagging.
- Handrails and balustrades. Give them a firm shake. A loose rail is the most serious failure on this list.
Replace damaged boards rather than trying to disguise them. If you find rot in framing, or the deck connects to the house in a way you do not understand, get a builder to look at it before you do anything cosmetic.
Cleaning
Sweep regularly and keep furniture and planters moving so they do not pin damp patches. Once a year, or when you see green algae or black mould, do a proper clean with a deck cleaner or a home-made solution and a stiff brush, then rinse thoroughly so no residue is left. Be careful with pressure washers. Used too close or too hard, they raise the grain and damage the surface, so keep the nozzle at a distance and work along the direction of the boards. Let the deck dry completely before you walk on it or apply anything.
Recoating
An oil or stain is there to slow the effects of UV and water, and it only works while it is intact. Recoat when water stops beading on the surface and starts soaking in. Some practical points:
- Apply to clean, dry timber, and give the product the drying time it specifies before walking on it.
- Sand rough or splintered areas first, working with the grain.
- If you are switching from one type of finish to another, the old finish usually has to be sanded back to bare timber first. Re-coating with the same type of product is simpler.
- Water-based products dry faster and are easier to clean up; oil-based products give a rich colour but take longer to dry.
- Protect adjacent cladding and paths with tape or drop sheets.
If your deck is hardwood, such as kwila or similar, follow the supplier's instructions for that species, since the natural oils in the timber affect how a new finish takes.
The rules owners overlook
Auckland Council's deck guide sets out several points that apply when you build or modify a deck, which can include replacing large sections. A deck up to 1.5 m high does not need a building consent, but may need a resource consent depending on the Unitary Plan. A deck more than 1 m high must have a handrail. And whatever the height, the work must comply with the Building Code, with foundations kept clear of public drains. The council's online checking tool does not cover decks above the ground floor or on steep, sloping sites; for those, contact the council.
Replacing a handful of boards is maintenance. Raising the deck, extending it, or changing how it attaches to the house is new building work. The council's page on building work you can do yourself points out that owners remain responsible for Building Code compliance even when no consent is needed.
When replacement beats repair
Patch repairs make sense for isolated boards. Replace the lot when boards are rotten across a wide area, when the framing is soft, or when the fixings have failed throughout. A deck on a bank, or one more than a metre or so above the ground, deserves a professional opinion, because a collapse is a safety issue rather than just an expense.